BY PLUMBING GUIDE FOR BATHTUB INSTALLATION

By Plumbing Guide for Bathtub Installation

By Plumbing Guide for Bathtub Installation

Blog Article

Quote

Presented here below you will discover lots of sensible insight involving A Step-by-Step Guide to Installing a Bathtub.


Tools You Need to Install a New Bathtub
Setting up a tub isn't exactly brain surgery, however it does need solid plumbing, woodworking, and also often, tiling abilities. Replacing an old bath tub with a new one is also a reasonably difficult project. If the old bathtub is conveniently available, the project can move easily; if you need to open a wall surface to remove the old tub and position the brand-new tub, the job is much harder. In either instance, the project is within a home handyman's skills, although you will need a helper to move out the old tub and embeded in the new one. Make certain you have actually certified on your own for the work and also are comfortable attempting it. Rather than hiring a specialist to take over a halfway-completed task, it is far better to take into consideration using one prior to you begin. Chances are you might need a specialist plumber to make tube connections.
This write-up will aid you set up a new tub in your shower room if you have actually already gotten a brand-new bathtub and don't require to change the arrangement of your previous water pipes.
Your devices as well as material checklist should make up the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Getting ready for the Installment


    Firstly, the supporting structure supplied with the bathroom ought to be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to see to it that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to prevent strain on the tub.
    Fit the versatile tap ports to the bottom of both taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you utilize all of the provided washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must currently prepare to be suited its final position.

    Removing Old Taps


    If you require to change old taps with new ones as a part of your installation, then the first thing you ought to do is separate the water system. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The procedure of removing the existing taps can be fairly troublesome because of the restricted gain access to that is frequently the case.
    Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipelines. When the supply pipelines have been removed, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
    Prior to proceeding to fit the new taps, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.

    Setting up the Bath tub


    Using both wooden boards under its feet, put the bathtub in the required setting. The wooden boards are practical in uniformly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four little points.
    The next goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bath tub until the level reviews level.
    To mount taps, fit all-time low of the outermost adaptable tap adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the other tap.
    Activate the water as well as check all joints as well as brand-new pipework for leakages as well as tighten them if essential. Fill up the tub as well as also inspect the overflow electrical outlet as well as the regular outlet for leakages.
    Ultimately, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the bathtub needs to wait till the bathtub has been made use of a minimum of once as this will certainly resolve it into its final position.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and also the other end offers a link to the current supply pipes.
    If you need to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
    Next off, position the tap in the installing opening in the bath/basin making certain that the washing machines remain in place in between the tap as well as the sink. Protect the tap in position with the producer offered backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former kind needs to be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.

    Tiling Around the Bath tub


    In the area where the bath meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split an inflexible seal, causing the water to penetrate the wall surface in between the bathroom and also the tiling, causing issues with wetness and possible leakages to the ceiling below.
    You can select from a selection of coloured sealants to assimilate your fixtures and fittings. They are offered in tubes and also cartridges, and also can securing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill up the bath tub with water before securing, to permit the motion experienced when the bathtub remains in use. The sealer can break rather early if you do not consider this activity before securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily offered on the marketplace. It is a good idea to fit the floor tiles using water-resistant or water resistant glue as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    Hopefully you liked our part on A Step-by-Step Guide to Installing a Bathtub. Thanks a lot for finding the time to read through our article post. Sharing is caring. One never knows, you may very well be helping someone out. Thanks a lot for going through it.


    Learn More

    Report this page